Great bike for both beginners and experienced riders, comfortable, good performance, and cheap to run! Bike is ready to go, see below for more details. The shift pedal and kickstand were replaced as a result. Bike was dropped last year coming out of a friend's driveway at low speed due to wet leaves. Good condition 2009 Yamaha FZ6R motorcycle in cadmium yellow for sale! I just took off that one screw holding the fairing in place, lifted it a little to fit the frame slider in and screwed it in.FS: 2009 YAMAHA FZ6R SPORT BIKE cadmium yellow (600cc) Afterwards Put the fairing back on and you're done with the left side! Step 4Īll you need to do for the right side of the bike is unscrew the engine bolt and screw in the frame slider. Parts Body & Frame Parts Frames & Accessories Frame Sliders 13495 FREE delivery April 28 - May 4. Screw in the bolt with your hands then use the socket wrench then torque it to manufacturer specs. Now install the left side of the frame slider That's just because I felt like it, I don't think you really have to. T-Rex Racing 2014 - 2020 CTX700 / CTX700n / DCT Frame Sliders () but here is the link of the 'sliders' on the front engine guards. Now I put some extra washers between the metal piece and when it makes contact with the bike. When you take them off and install the metal piece that came with the Frame Slider kit make sure you see the little cut, it looks like a slant cut, it should look like this on the left side: There are two engine bolts you need to take off on the left side of the bike to install the metal plating for the frame slider to rest on since it's a No-Cut. Taking off the engine bolts, installing the frame slider The fairing was still hooked on by the turn signal wire and the screw at the bottom of the fairing, be careful not to slam it hard or it'll break off. Now when I took it off, it looked like this: >Important!! Make sure you have something close to the bike or underneath it so you can rest the fairing on it! Otherwise you'd scratch the fairing with the pavement. There are 3 screws on top, another on the right which is bigger than the ones on top and the two screws on the bottom. Start taking off the screws of the fairing on the left hand side, make sure you work on one side at a time so you don't mess up the screws or lose parts. TRex Racing 2013 On Yamaha FJ 09 Frame Front Fork Rear Axle Case Sliders Crash Protectors COMBO. T-Rex Kit, front/rear axle sliders, frame sliders, engine case guards and a free set of swingarm spools. There are a lot of choices out there, woodcraft cuts are one of. Cuts are stronger than no cuts because it's mounted directly on the frame where you have to cut a little bit of the fairing, where as no cuts is mounted on an off bracket that could snap. Also refer to the Owner's Manual if you are unsure about how to take off the fairing) At the time the T-Rex kit was not available, and its to bad because get everything you need for a good price. First thing is what do you want, no cut or cuts. Step 2: (You can start working on either side of the bike, I'll just post this side first and later on I'll post the other side. Custom powdercoating colors (anything other than black) can take an additional 2 weeks. Black R3 cage is in stock and can ship within 24 hours These are built-to-order cages and can take up to 6-8 weeks for production due to high demand. After you have the screws off, take off the plastic piece. Currently available for R3, R6, R6R, R1, and FZ6 (not FZ6R). Keeping engine fluids inside the engine is our main objective with our protection parts. From street accidents to 100mph high-sides nothing will help prevent costly damage more than a set of our sliders. It's held on by 4 screws that need a hex key to take off. Woodcraft Frame Sliders are one of the smartest investments you can make to your bike. Take off this lower cowling at the bottom of the front of the bike Make sure the engine is cool when you start this process, otherwise you'd burn your hands on it or the hot engine bolt when trying to remove it! Step 1: Socket Wrench/Torque Wrench (To take off the engine bolt and install Frame Sliders)įirst, I ordered the Intuitive No-Cut Frame Sliders because T-Rex was on back order and I had many close calls. Hex Key/Allen Key (To Take off the fairing) Task is pretty easy all you need is a couple of tools: Hey all, just got done installing my Frame Sliders for the first time and I had a little difficulty so I just snapped some pictures while I was doing it to help people who had problems or are scared to do it themselves.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |